TWIN BENCHTOP – WITH SEDIMENT AND DISRUPTOR FILTER

System: 270 W x 300 H x 110 D (mm)

Filters: 9″ x 2.5″ each.

Sediment Filter – Contaminant Reduction

• Particles >1 micron……………99.999% (Sand, silt, rust, clay, algae)

Disruptor® Filter – Contaminant Reduction

• PFOA (Perfluorooctanoic Acid) > 98.9%
• PFOS (Perfluorooctane Sulfonic Acid) > 99.0%
• Total Chlorine (Chloramines) > 99.3%
• Free Chlorine > 99.5%
• Lead (Pb) > 99.4% @pH 6.5
• Lead (Pb) > 99.4% @pH 8.5
• Copper (Cu) > 99.9% @pH 8.5
• Copper (Cu) > 99.9% @pH 6.5
• E.Coli (Total Coliforms) > 99.9999%
• Coliphage (Bacterial Virus) 99.9995%

• 1st Stage Filter: 100% Polypropylene triple gradient sediment filter.
  • Capacity: Dependant on Water Quality
  • Protects the lifespan of downstream filters by removing dirt, sand, and rust, and preventing premature blockages.
  • Triple gradient Sediment Filter
  • Porosity: 1 Micron Nominal

• 2nd Stage Filter: Combines electroadsorptive nanotechnology, high-performance activated carbon block, and submicron membrane filtration to deliver advanced, multi-stage contaminant reduction — all in a single, compact unit.
  • Capable of filtering 7,000 litres  at a flow rate of 3 lpm.
  • Combines Mechanical, Electrical, Adsorption and Nano Filtration Technologies
  • This filter works not only with Tap Water or Town Water, but also works for Rainwater, Spring Water, Dam Water and River or Creek Water.
  • Porosity: 0.5 Micron Nominal

• To ensure optimal performance and hygiene and to prevent build up of contaminants, we recommend that filters are not used any longer than 12 months. However, replacement frequency depends on water quality and usage.
• Filters should also be changed when rated capacity is reached, or when flow becomes too slow.

Find here 9″ Sediment and Disruptor® Replacement Filters

Kitchen Faucets Compatible with the Countertop Water Filter:

Countertop Water Filter Tap Fittings:

⚠️  This system is for use on cold water line only. Hot water may damage the system.

FITS ON SINGLE HANDLE OR DOUBLE HANDLE FAUCET

IF YOUR FAUCET IS WITH INNER THREADS OF SPOUT

1. TAKE OFF THE AERATOR FROM THE FAUCET

2. PUT THE ADAPTOR AND RUBBER WASHER INTO THE FAUCET AND TIGHTEN IT

3. REVOLVE DIVERTER VALVE INTO THE ADAPTOR

IF YOUR FAUCET IS WITH THREADS OUTSIDE OF SPOUT

1. TAKE OFF THE AERATOR FROM THE FAUCET AND REVOLVE THE DIVERTER VALVE INTO THE FAUCET DIRECTLY. PLEASE CHECK IF THERE IS AN O-RING INSIDE THE DIVERTER VALVE.

TO FIT TO NON-THREAD FAUCET

IF YOUR FAUCET IS 1/2″ OD ABD WITHOUT THREAD

1. INSERT RUBBER INTO EXTERNAL ADAPTOR.

2. PUT EXTERNAL ADAPTOR ON THE FAUCET AND TIGHTEN THE NOSE CLAMP BY SCREWDRIVER.

3. REVOLVE THE DIVERTER VALVE INTO THE EXTERNAL ADAPTOR.

IF YOUR FAUCET IS 3/4″ OD AND WITHOUT THREAD

1. PUT EXTERNAL ADAPTOR ON THE FAUCET AND TIGHTEN THE HOSE CLAMP BY SCREWDRIVER (NO NEED RUBBER)

2. REVOLVE THE DIVERTER VALVE INTO THE EXTERNAL ADAPTOR.

How often should I replace the filters?

• 1st Stage: SEDIMENT FILTER: 200 gal (6-12 Months)
• 2nd Stage: DISRUPTOR FILTER CARTRIDGE: 1,850 gal (1 Years)
• Note: Filter capacity also varies dependant on water quality.

Are sediments in water harmful?

Sediment increases the cost of treating drinking water and can result in odour and taste problems. Sediments can clog 2nd stage filters, especially fine carbon blocks.

⚠️  This system is for use on cold water line only. Hot water may damage the system.

• Min. Operating Temperature: 0.6 °C
• Max. Operating Temperature: 38 °C
• Min. Working Pressure: 25 psi
• Max. Working Pressure: 125 psi
• Flow Rate: 3 LPM

• For Cold water use only. Install on COLD water lines only.
• Never install or operate where inlet water pressure may exceed 120 psi (827kPa)
• Protect from freezing. Remove filter if temperature drop below 1°C.

Contents:

• 2 x 9” x 2.5” Water Filter Housing Sump
• 1 x Ctop Stand
• 1 x Ctop Inlet w/ Spout
• 1 x Ctop Hose
• 1 x Ctop Adaptor
• 1 x Diverter
• 2 x Filter Cartridges
• 1st Stage: SEDIMENT FILTER
• 2nd Stage: DISRUPTOR FILTER CARTRIDGE

• Sediment Filter – Certifications:
  • Tested and Certified by NSF International under NSF/ANSI Standard 42 for material requirements only and and FDA CFR Title 21.

• Disruptor® Filter – Certifications
  • Tested to NSF/ANSI 42 & 53 aesthetic effects and health effects testing.
  • Independently laboratory tested by SGS for proven performance, including rigorous volume-based testing to ensure consistent purity throughout its lifespan.