TWIN BENCHTOP – WITH SEDIMENT AND CARBON FILTER

System: 270W x 300H x 110D.

Filters: 9″ x 2.5″ each.

• Sediment Filter – Contaminant Reduction
  • Particles >1 micron………..…99.99%
• Carbon Filter – Contaminant Reduction
  • Particles >1 micron…………………99.999% (0.4 Micron Nominal Filtration)
  • Lead (Pb)……………………………>90%+
  • Chlorine……………………………..>95%
  • Cyst (Giardia, Cryptosporidium)…>99.99%

Performance has been tested and certified by independent laboratory testing in both Australia & the USA.

• Sediment Pre-Filter – Replace every year
  • 100% Polypropylene Triple Gradient Sediment Filter.
  • Triple Gradient or Triple Layered means its outer layer has 10 microns, the middle layer has 5 microns and the inner layer (core) has 1 micron. This prevents filters blocking prematurely and provides a higher contaminant holding capacity. Instead of dirt building up on the outside, like regular sediment filters, dirt is trapped throughout the whole filter.

• Stage 2: Carbon Filter – Replace every year
  • Carbon: The Carbon Filter is highly effective at reducing Chlorine, Cysts, Taste, Odours, Lead (Heavy Metals), VOC’s from potable drinking water.
  • Made in USA by Omnipure. Coconut Shell Activated Carbon Media with Lead removal media.
  • Capacity: 7.500 Litres
  • Made in USA by Omnipure

• To ensure optimal performance and hygiene and to prevent build up of contaminants, we recommend that filters are not used any longer than 12 months. However, replacement frequency depends on water quality and usage.
• Filters should also be changed when rated capacity is reached, or when flow becomes too slow.

Find here 9″ Sediment and Carbon Replacement Filters

Kitchen Faucets Compatible with the Countertop Water Filter:

Countertop Water Filter Tap Fittings:

FITS ON SINGLE HANDLE OR DOUBLE HANDLE FAUCET

IF YOUR FAUCET IS WITH INNER THREADS OF SPOUT

1. TAKE OFF THE AERATOR FROM THE FAUCET

2. PUT THE ADAPTOR AND RUBBER WASHER INTO THE FAUCET AND TIGHTEN IT

3. REVOLVE DIVERTER VALVE INTO THE ADAPTOR

IF YOUR FAUCET IS WITH THREADS OUTSIDE OF SPOUT

1. TAKE OFF THE AERATOR FROM THE FAUCET AND REVOLVE THE DIVERTER VALVE INTO THE FAUCET DIRECTLY. PLEASE CHECK IF THERE IS AN O-RING INSIDE THE DIVERTER VALVE.

TO FIT TO NON-THREAD FAUCET

IF YOUR FAUCET IS 1/2″ OD ABD WITHOUT THREAD

1. INSERT RUBBER INTO EXTERNAL ADAPTOR.

2. PUT EXTERNAL ADAPTOR ON THE FAUCET AND TIGHTEN THE NOSE CLAMP BY SCREWDRIVER.

3. REVOLVE THE DIVERTER VALVE INTO THE EXTERNAL ADAPTOR.

IF YOUR FAUCET IS 3/4″ OD AND WITHOUT THREAD

1. PUT EXTERNAL ADAPTOR ON THE FAUCET AND TIGHTEN THE HOSE CLAMP BY SCREWDRIVER (NO NEED RUBBER)

2. REVOLVE THE DIVERTER VALVE INTO THE EXTERNAL ADAPTOR.

How often should I replace the filters?

• To ensure optimal performance and hygiene and to prevent build up of contaminants, we recommend that filters are not used any longer than 12 months. However, replacement frequency depends on water quality and usage.

• Min. Operating Temperature: 0.6 °C
• Max. Operating Temperature: 38 °C
• Min. Working Pressure: 25 psi
• Max. Working Pressure: 125 psi
• Flow Rate: 3 LPM

• For Cold water use only. Install on COLD water lines only.
• Never install or operate where inlet water pressure may exceed 120 psi (827kPa)
• Protect from freezing. Remove filter if temperature drop below 1°C.

Contents:

• 2 x 9” x 2.5” Water Filter Housing Sump
• 1 x Ctop Stand
• 1 x Ctop Inlet w/ Spout
• 1 x Ctop Hose
• 1 x Ctop Adaptor
• 1 x Diverter
• 2 x Filter Cartridges
  • 1st Stage: SEDIMENT FILTER
  • 2nd Stage: OMNIPURE CARBON FILTER

• Sediment Filter – Certifications:
  • Tested and Certified by NSF International under NSF/ANSI Standard 42 for material requirements only.

• Carbon Filter – Certifications
  • Certified by NSF 42 and 53 for reduction claim and material requirements.
  • See Omnipure List of Certified products under NSF.